• ECN (Engineering change details)

    I want to know how to get Engineering change content reports & all details from revision to revision.
    vishal.arora
    last modified by vishal.arora
  • Valor Process Prep conflict with Excel

    I keep getting an error when I try to save my documentation session, it says it cannot write to the file (TDP_Document).  Because of that, I can't save an check in my project so I lose all of my edits.  Some...
    glennb451
    last modified by glennb451
  • Ineffective pattern generation detected. Terminating the current ATPG session

    #tessent  How is  Ineffective pattern generation detected. Terminating the current ATPG session. how tessent tool determining ineffective patterns ?
    edname
    last modified by edname
  • do file command to compile all out of date

    I am using ModelSim PE 2019.1.  Is there a command that I can add to my my "*.do" file that will recompile all out of date source files without entering them individually?
    wds
    last modified by wds
  • Mentor Ideas for Mentor Communities

    Background: I started creating contents in Mentor Communities and would like to share enhancement ideas and bugs found on the Mentor Communities engine itself.   Question: Would it make sense to create a space&#...
    fabienlaunay
    last modified by fabienlaunay
  • Global or OFF page connector

    This symbol represents ? and what is the Purpose of it?
    anbu
    last modified by anbu
  • Jumping to top in Contentview not working

    This is the situation: when you go into the content section of this forum - no matter what your filter settings are set - and you like to go to the next page, you don't get any feedback of it ... well no other than t...
    ton.s
    last modified by ton.s
  • Problem temperature fluid out,

    Dear, I have ran a calculation on FloEFD, but the results I have obtained is not correct. I have verified it by i basic formulation: mCpDT. I have verified my boundary conditions and I think there are no problems o...
    bayelahad
    last modified by bayelahad
  • Problems of temperature results

    Dear, I have ran a calculation on FloEFD, but the results I have obtained is not correct. I have verified it by i basic formulation: mCpDT. I have verified my boundary conditions and I think there are no problems o...
    bayelahad
    last modified by bayelahad
  • How to modify the Steinmetz coefficients when considering a bulk conductivity?

    Hi everyone!   I am using MagNet and I need to make iron loss calculations for my model. I am wondering how to modify the Steinmetz coefficients if we consider a non-zero conductivity for the iron?
    khamitov
    last modified by khamitov
  • How do I mark a document as helpful?

    I see how to "like" it, but not how to mark it as helpful. I can only mark comments as helpful.   Thanks,   Jeff
    jleine
    last modified by jleine
  • T3Ster Golden Reference

    How do one use the "golden Reference" for the T3Ster System? Is there a manual explaining how the calibration works with this reference or atleast an information Sheet?   Any Knowledge about this would be help...
    wagner1
    created by wagner1
  • Electrical System Design and Harness Engineering Feedback

    Search does not appear to be working.   Regards, Pat
    Pat
    last modified by Pat
  • [Motorsolve] Cannot solve motor thermal analysis

    Hi Pals,   I tried to build a BLDC halbach servo motor with related KB article reference. I can run regular motor performance and field analysis, but I found that I cannot run thermal analysis. A error window wi...
    wingston99
    last modified by wingston99
  • Figures and using geometry to project

    Hello, just installed Cadra 23. When installing a figure into a view, I cannot use the geometry to project to other views. It gives me the warning "no valid selection". On Cadra V22, I did not have this problem. Is t...
    eddiea
    last modified by eddiea
  • Tables on drawing generated using Plug in  gets disappear when user makes any change in Design.

    You do not have access to this content's place
    khakaresatish
    created by khakaresatish
  • change of community "credentials" (username, reference email ...)

    Dear Community / Community Admin,   how do I change my username, or reference email ? Is there any way to do so ?   I went through a few quick Start guides (*.docx) posted in this Forum, but nothing. ...
    fuba
    last modified by fuba
  • ok i give up...how do i get the origin axes off my screen? 

    once you start a flow analysis, a bounding box representing the fluid domain appears.  it has green x/y/z axes at its origin.  these axes will not go away
    jacob.grayson
    last modified by jacob.grayson
  • Inability to attach a file to an Idea comment or reply

    When I initiate an Idea or Discussion, in the lower right corner of the editor, I have the ability to attach files.  And, if I reply to a Community discussion or question, I have the option to use the advanced ed...
    .-.--.--
    last modified by .-.--.--
  • How can I change the Log In person on my computer?

    My Manager logged in on my computer and now it automatically logs in as him.  How can I change or clear his log in so I can log in with my credentials?   Thank You!
    khillers
    last modified by khillers