• How to enable the remap layer?

    I want to add layers on my PANEL but it is disabled. Please see attached image. Thank you.
    hbenawe
    last modified by hbenawe
  • Automation in Python

    I am trying to learn automation in python. I have looked in the AATK, but the only example included for python fails with errors. Will someone give me an example of code in python for validating the pdbDoc? I am using...
    wayne_5757
    created by wayne_5757
  • Backdrill Analasys missing from Output menu

    Hi Folks,   For some weird reason, the 'Backdrill Analysis" is missing from the output menu. We have tried to solve this by running the registrator again, deleting the WDIR and even checked the addin.ini file to...
    charles.ietswaard1
    last modified by charles.ietswaard1
  • Via disappears during placement

    Hello, I got a Problem and I can't find the solution. I got 2 Pads which are connected by a plane on Layer 1. I can place a microVia and a blind Via in one Pad, but the if I try to place the second Mico+Blind the Mi...
    manuel_k
    created by manuel_k
  • How to add net to the NC pins of a component in PCB layout?

    Is it possible to put nets like make it GND or VCC of NC (or no nets) pins on components in PCB layout?
    hbenawe
    last modified by hbenawe
  • Maximum Trace width and clearance

    What is the maximum trace width and clearance that can be set within CES. I have tried to set a trace width of 30mm and get an error that the maximum allowed is 25.4mm Is this value fixed within MG - or can it be al...
    greghall
    last modified by greghall
  • Padstack - Shorted_Nets_by_Layer

    Hello fellow designers,   Long time PADS user here but a newbie into Xpedition....so please bear with me.   I like this capability of shorting a net by layer in a padstack, however, I haven't figured out h...
    ChangeMe_116199
    last modified by ChangeMe_116199
  • Batch and Online DRC have difference

    Hello dears,   We started to use Package Clearance Type Rules. But it seems that Batch and Online DRC have difference. Online DRC doesn't detect the error, but Batch DRC detects it. Therefore we can place the pa...
    fuji
    created by fuji
  • FABLINK: How To Change Layers Quantity And Board Stack-up In A Template?

    Hello dears Mentor Guru, please give me some advice. I have tried to change layers quantity in the Fablink from 4 to 2 without any success. Stack-up also not possible to change. Where to find or how to create templa...
    pinus
    last modified by pinus
  • dxf file

    How can I add a dxf file to a PCB?
  • How to enable project file?

    I want to do forward annotation but it seems not possible due to disabled project file. Please see attached image.   Thank you.
    hbenawe
    last modified by hbenawe
  • Import PCB into New Template

    I would like to use my existing Job parameters file that contain all needed info in Xpedition Layout. This new PCB Layout was a conversion and doesn't have all my standard configs.   Overall, I'd like ...
    aiewould
    last modified by aiewould
  • Using VX2.6, how do we detect the height of all the SILK or SILKSCREEN used in PCB?

    I wonder if we created report writer or maybe there is an script to check the SILKSCREEN height used in the PCB.
    hbenawe
    last modified by hbenawe
  • Layer Stackup DRC

    Hi All,   In VX? the Layer Stackup DRC was introduced. Assuming Xpedition is a professional package, a total waste of effort/resources, in my humble opinion. (but who am i).   As an research Institute we d...
    charles.ietswaard1
    last modified by charles.ietswaard1
  • How to replace part/component in (Expedition) Layout?

    Is there a way to replace part/component  (change to another package/cell)  directly in EXPEDITION Layout? I tried using ECO>Replace Cell, but it doesnt allow the replace option. Reset is the only option...
    hbenawe
    last modified by hbenawe
  • OrCad Schematic to Xpedition Layout Free Browser cross probe

    Hi All,   Is there any way or 3rd part SW that can cross probe between OrCad to  Xpedition free browser ? With the full Layout and Pads I found and it works...   Thanks,   Nadav
    nadav_azulay
    created by nadav_azulay
  • Fablink Gerber output format

    Probably a basic question, but just after some clarification. Currently we output gerber files (and NC Drill data) from Fablink - now I believe that this is in 274X Gerber format. (that's what it says on the dialog s...
    greghall
    last modified by greghall
  • How to enable route mode in FABLINK?

    hbenawe
    last modified by hbenawe
  • How to enable import/export edx and pdf output in library manager (xpedition layout)?

    Please see attached file. Thank you so much.
    hbenawe
    last modified by hbenawe
  • Is there a shortcut to delete all PARTS not used in XPEDITION layout aside from deleting them one by one?

    I have an expedition PCB. There are many PART declared in the local LIB. I want to retain only the 10 components that was used in the design.
    hbenawe
    last modified by hbenawe