3 Replies Latest reply on Nov 28, 2018 12:37 AM by jacktan

    Error During saving part type in Central library

    sachin78

      I am Using pads VX2.1, in pads library it allow to modify or create part but finally gives message "Error During saving part type in Central Library"

      if anybody goes through such problem please help.

        • 1. Re: Error During saving part type in Central library
          jacktan

          I encounter the same problem as the above.

          The part type never gets written into the central library.

          I changed the security access settings to READ/WRITE for everyone for the following files, all to no avail.

          .lmc file, the symbolib, PADSLibs, CellDBLibs, PartsDBLibs etc.

          Please help, this is becoming urgent because without the ability to add new part type to the central library,

          basically we are stuck.  Thank you.

          • 2. Re: Error During saving part type in Central library
            cathy_terwedow

            Sachin, Jack - please log service requests for these issues. Your descriptions are too vague to answer here.

            • 3. Re: Error During saving part type in Central library
              jacktan

              I import PADS library into my PADS Integrated central library (.lmc) using xDX Designer PADS Library Tool.

              It resulted in a log that says the parts are skipped as they exist in the library already.

              But when I searched the library, they do not exist.

              See log under [E] errors, where it says creation skipped due to parts exist.

               

              Symbol and Schematic Translator for xDX Designer

              Release: PADS VX.2.1

              Install Id: 1468892

              Copyright 2016 Mentor Graphics Corporation.  All Rights Reserved. Mentor Graphics Corporation

              Translation start: 28/11/2018 2:34:36 PM

              Input file: C:\MentorGraphics\PADSVX.2.1\SDD_HOME\Libraries\temp.pt9

              [I] Loaded bus contents file: C:\PADS Projects\DxProjects\NTB3_POE\busconts.ini

              File type: (1,3) PADS Logic binary library Part Types

              Output path: C:\PADS Projects\DxProjects\NTB3_POE

              [I] Successfully loaded property definition file: 'C:\ODA_Starter_Library\PADS_Library\PADS_Integrated_Library\CentLib.prp'

              [I] Smart library merge: Updated partition reference for symbol temp:DF3A-4P-2DS => Connector:DF3A-4P-2DS

              [I] Smart library merge: Updated partition reference for symbol temp:FTS-103-01-F-DV-TR => Connector:FTS-103-01-F-DV-TR

              [W] Skipped existing symbol: FTS-103-01-F-DV-TR.1

              [W] Skipped existing symbol: DF3A-4P-2DS.1

              [I] Running CLPartSync: 'Connector' partition

              [I] Creating new CL partition: 'Connector' on 'C:\ODA_Starter_Library\PADS_Library\PADS_Integrated_Library\PADS_Integrated_Library.lmc'

              [E] Part Number creation skipped because already exists in Library: 'DF3A-4P-2DS'

              [E] Part Number creation skipped because already exists in Library: 'FTS-103-01-F-DV-TR'

              [I] Running CLPartSync: 'temp' partition

              [I] Creating new CL partition: 'temp' on 'C:\ODA_Starter_Library\PADS_Library\PADS_Integrated_Library\PADS_Integrated_Library.lmc'

              [I] Updated property definition file: 'C:\ODA_Starter_Library\PADS_Library\PADS_Integrated_Library\CentLib.prp'

              [O] Created 0 symbol(s) and 0 schematic sheet(s)

              2 error(s) and 2 warning(s) found

              Finished on 28/11/2018 at 2:34:43 PM.