• Selection of Net Connection Basis on Net Segment

    I have selected a Net segment on schematic which is only connected to Pin10 of U1. But i am not able to get this connection only and getting lets say five more connection those are based on other segments of this same...
    last modified by deepakagarwal
  • can`t close DxDesigner /viewdraw at the end of script !

    Hi,   I wanted to write a script which will exit the current runing designe. But if i run the  Quit method at the end of the scriptlines I geth this message:       any Idea ? is this new ...
    last modified by christopher.branch
  • Is it possible at BoardSim level to move stack-up layers?

    Hi, after a SERDES analysis I've seen that I might have a crosstalk problem related to adjacent layer nets. Is there a way to rearrange layers in order to perform again the SERDES compliance analysis with that stack-u...
    created by jjmoran
  • Finding mentor compatible part for Xpedition 

    Hi,  I am looking for mentor compatible part "surface mount RF transformer ADT1-1WT". I need to add symbol and footprint packaged as part. I have looked at Part Quest but don't find it there. Any idea ...
    last modified by joniengr081
  • Minimum distance tool in Xpedition PCB

    Hi,  I am not able to use the minimum distance tool upon right click in Xpedition PCB to find distance between two points in placement mode. It calculates the distance from edge, corner or from center. How can I...
    last modified by joniengr081
  • Quick Search Value or Decal and Editing

    Hi I have a question.   In PADS Logic, is there anyway I can do a quick search for same "Value" or "Decal", and furthermore, edit or work with the found items?   I have included a reference from other tool...
    created by suchengyu
  • Script for add Rectangle Plane

    I'm using Xpedition Layout VX.2.6. I need to add a Rectangle Plane from selected vias or any selected objects automatically. Example as picture below: Is there anyone know how to write a script or have a scri...
    last modified by khang
  • Variants Question

    Hello, I have a question about using Variants Manager in PADS Designer VX2.4 Integrated Flow.    Our company has setup Central Library but maybe not in a complete way.. Central Library has all unique s...
    created by e_cornell_ldpxt

    we are simulating DDR3, in the DDR3 Wizard setup i have an doubt in simulation option, in the section measurements location for DDR & Controller what has to be enable either die/pin.
    last modified by ecs
  • urgent need help

    # # Please go to http://www.model.com and download an updated copy of the ModelSim PE Student Edition. # Error loading design   I have downloaded four times and put license in correct folder but still I am gett...
    created by kyuripark
  • Hyperlynx VX2.4 Digital Oscilloscope Eye-Diagram configure window not opening

    Hi,   I am using Hyperlynx VX2.4. I tried to do an eye-diagram simulation and when I tried to configure the eye mask and other parameters using the eye-diagram configuration file, this window is not displayed. ...
    last modified by roberto.torres@harman.com
  • Need help for SERDES Batch Simulation

    Hi, I'm performing SERDES Batch Simulation to some nets of a board that are driven from a Mezzanine card to a Virtex FPGA. The problem is that I only have IBIS-AMI model of the FPGA, but I'm missing connector model a...
    last modified by jjmoran
  • Exporting a Netlist form PADS designer without constraints

    Hi, I am using PADS Designer (VX.2.6) with PADS Layout (VX.2.6) in the traditional workflow (using netlists, not integrated). I need to make a modification to an existing design that I did not do myself. This design ...
    last modified by jlbouchard
  • Who has a simulation model for a twisted pair cable?

    I search for a model to simulate a CAT-5 cable in HyperLynx SI. HyperLynx does not provide a model for this standardizrd cable type (The standard is EIA/TIA-568). The conductors are regular copper wires, but since the...
    last modified by c.alscher
  • Problem while adding Net Attribute

    I would like to add a property (string) to specified Net selected. I successfully achieved it but the property value is coming only in NAME=VALUE format. Like for example i want to add property to the NET say "Hangin...
    last modified by deepakagarwal
  • Assembly drawing with layer 1 dimmed

    Is it possible to create that kind of assembly drawing where layer 1 can be seen dimmed at background. Similarly bottom layer if there are components at bottom side. Pads layout VX2.5
    last modified by kyosti.hatunen@sulzer.com
  • Hyperlynx : DRR3 Batch Simulation Data Read Problem

    We are simulation DDR3L in our design and we are trying to simulate our chips through Hyperlynx DDR3 batch simulation. We have used one slot dual ranked settings. After setting the parameters required for DDR3 batch s...
    last modified by m.ather
  • Part Lister: Replace one property with another

    How do I set up a rule in the IPL file, to replace one property value with another?   I.e. I would like a rule that detects if 'Part Number' starts with 'X', and if so, it will drop that value and instead use th...
    last modified by lennart.edenfjord1
  • Reset Text Properties on Symbol in DxDesigner

    I need to reposition the properties and reset text properties for all symbols on my DxDesigner schematic.   In the schematic if your right click the symbol you should see both of those options in the pop up menu...
    last modified by andrew_french
  • How can i execute the command (Preposition Properties) in the command popup menu?

    I like to execute the "prepostion properties" command in the component pop up menu. How can i do that. Is it possible to select the command item and use a method like "click"? Thanks for your help in advance!   ...
    last modified by joerg.schmidt